©2008 Pella Corporation
Part Number: 80GY0102
INSTALLATION INSTRUCTIONS - INSTRUCCIONES DE INSTALACION
FOR HURRICANESHIELD® IMPACT-RESISTANT
CASEMENT AND AWNING WINDOWS IN WOOD FRAME CONSTRUCTION
These instructions were tested and are Dade County certified for single laminated glass and ASTM
(Hallmark) certified for laminated insulating glass.
Important Safety Information:
Pella® HurricaneShield® products have been tested in accordance with the large missile impact
testing requirements of ASTM E 1886 and ASTM E 1996. Pella HurricaneShield products are
neither hurricane proof nor are they shatter proof. Severe wind and rain may produce temporary
conditions which exceed product performance standards. When these units are subjected to intense
storms or extreme conditions, which exceed the intended design pressures, air, water and flying debris
infiltration may occur. The performance of any building is dependent upon the design, installation,
and workmanship of the entire building system. Pella Corporation strongly recommends consulting
an experienced architect, contractor, or structural engineer prior to installation of Pella products.
The individual (building owner, architect, contractor, installer and/or consumer) responsible for the
project must take into account local conditions, building codes, inherent component limitations,
the effects of aging and weathering on building components, and other design issues relevant to each
project. The determination of the suitability of all building components for each project, as well
as the design and installation of flashing and sealing systems, are the responsibility of the building
owner, architect, contractor, installer and/or consumer.
5PQꢀ'MBTIJOHꢀ5BQFT
'JO
$PSOFS
/BJMJOHꢀ'JO
$PSOFS
'MBTIJOH
5BQF
$PSOFS
'MBTIJOH
5BQF
4JEF
'MBTIJOH
5BQF
4JEF
'MBTIJOH
5BQF
8JOEPXꢀ#PUUPN
4JMMꢀ'MBTIJOHꢀ5BQFꢀꢁꢃ
4JMMꢀ'MBTIJOHꢀ5BQFꢀꢁꢂ
8BUFSꢀ3FTJTUJWFꢀ#BSSJFS
4IFBUIJOH
'SBNJOH
Always read the Pella® Limited Warranty before purchasing or installing Pella products. By installing
this product, you are acknowledging that this Limited Warranty is part of the terms of the sale.
Failure to comply with all Pella installation and maintenance instructions may void your Pella
product warranty. See Limited Warranty for complete details at http://www.pella.com.
D. Fold the water resistive barrier (1D). Fold side and bottom flaps
into the opening and staple to inside wall. Fold top flap up and
temporarily fasten with flashing tape.
&YUFSJPS
E. Apply sill flashing tape #1. Cut a piece of flashing tape 12"
longer than the opening width. Apply at the bottom of the
opening as shown (1E) so it overhangs 1" to the exterior.
ꢀ%
Note: The tape is cut 12" longer than the width so that it
will extend 6" up each side of the opening.
ꢃꢈ
ꢃꢈ
ꢀ&
ꢌꢈ
ꢀ(
ꢃꢋꢂꢈ
ꢃꢋꢂꢈ
ꢀ'
F. Tab the sill flashing tape and fold. Cut 1" wide tabs at each corner (1/2" from each side of
corner) (1F). Fold tape to the exterior and press firmly to adhere it to the water resistive barrier.
G. Apply sill flashing tape #2. Cut a piece of flashing tape 12" longer than the opening width.
Apply at the bottom, overlapping tape #1 by at least 1". DO NOT allow the tape to extend
past the interior face of the framing (1G).
Note: The flashing tape does not need to extend all the way to the interior of the framing.
H. Install and level sill spacers. Place 1" wide by 1/4" thick
ꢀ)
spacers on the bottom of the window opening 1/2" from each
side. Spacers are also required at points where windows are
joined in multiple window applications. Add shims as necessary
to ensure the spacers are level. Once level, attach spacers and
shims to prevent movement.
Note: Improper placement of shims or spacers may result in
bowing the bottom of the window.
PREPARING THE WINDOW
2
A. Remove plastic wrap and cardboard packaging from window. DO NOT remove plastic
shipping spacers located between the window sash and frame. The shipping spacers will help
keep the window square during installation. DO NOT unlock or open the window until it is
fully fastened.
Note: If screens, grilles or hardware are removed from the window at this time, label them
and store them in a protected area.
B. Windows using Frame Screws:
On the roomside of vent windows, drill 13/64" diameter clearance holes through the head,
jambs and sill of the frame. Space the holes using the maximum end and on center spacings
as shown on the placement diagram.
Note: On vent casements, place the holes so that they do not interfere with the roto
operator and the latch points on the lock side of the window.
1-"$&.&/5ꢀ%*"(3".
'PSꢀQMBDFNFOUꢀPGꢀ'SBNFꢀ4DSFXTꢀ
BOEꢀ*OTUBMMBUJPOꢀ$MJQTꢍ
%SJMMꢀꢃꢄꢋꢌꢅꢈꢀ
DMFBSBODFꢀIPMFꢀ
UISPVHIꢀGSBNFꢀBUꢀ
BꢀꢅꢉꢀEFHSFFꢀBOHMFꢀ
ꢌꢈꢀ."9
ꢁ#
ꢃꢉꢈ
."9
ꢁ#
ꢃꢉꢈ
."9
ꢄꢋꢃꢌꢈꢀ
.BYꢊ
ꢃꢉꢈ
."9
%SJMMꢀꢃꢄꢋꢌꢅꢈꢀ
DMFBSBODFꢀIPMFꢀ
UISPVHIꢀGSBNFꢀ
ꢌꢈꢀ."9
ꢅꢈ
ꢃꢉꢈ
ꢅꢈ
."9
."9
."9
C. Fold out installation fin to 90°. Be careful not to remove
ꢁ$
or tear the fin corners.
Note: If the fin is not at 90°, the window will not line
up correctly on the interior.
ꢁꢌꢀYꢀꢉꢋꢇwꢀDPSSPTJPO
SFTJTUBOUꢀTDSFXT
ꢌiꢀGSPNꢀFOE
D. Windows using Installation Clips:
Install installation clips. Place the clip so
that the lip is facing up and against the
installation fin, at the locations shown in
the placement diagram. Secure the clip
by driving #6 x 5/8" corrosion resistant
screws through the outer two holes of
the three holes shown.
-JQ
ꢁ%
SETTING AND FASTENING THE WINDOW
3
ꢂ"
TWO OR MORE PEOPLE WILL BE
REQUIRED FOR THE FOLLOWING STEPS.
A. Insert the window from the exterior of the building. Place
the bottom of the window on the spacers at the bottom
of the opening, then tilt the top into position. Center the
window between the sides of the opening to allow clearance
for shimming, and insert one roofing nail in the first hole
from the corner on each end of the top nailing fin. These are
used to hold the window in place while shimming it plumb
and square.
B. Plumb and square window. Place shims
between the window frame and the rough
ꢂ#
*OUFSJPS
opening at each installation screw hole.
Adjust the shims as required to plumb
and square the window in the opening.
Windows with Installation Clips only:
Shim between each installation clip and
the rough opening.
ꢂ#
Note: DO NOT over shim.
C. Check the interior reveal. Make sure the
measurement from the interior face of the
window to the interior face of the wall
is equal at several points around the
window.
ꢂ$
ꢀ
*/$)&4
ꢃ
NN
ꢁ
ꢃ
ꢁ
ꢂ
ꢄ
ꢃ
ꢂ
ꢅ
ꢃ
ꢆ
ꢃ
ꢇ
ꢃ
Note: If the dimensions are not
equal, check to make sure the fins
are folded out to 90° at all points.
D. Check window operation (vent units only). Remove the shipping
spacers, unlock the window and open and close it a few times to check
for proper operation. Close and lock the window.
Note: If there are any problems with the operation of the window,
recheck shim locations and adjust for plumb and square.
ꢂ&
E. Fasten the window to opening by driving 2" galvanized
roofing nails into each pre-punched hole in the nailing fin.
Note: Make sure the fin corner is lying as flat as possible.
INTEGRATING THE WINDOW TO
4THE WATER RESISTIVE BARRIER
Note: The flashing tape must be applied approximately 1/2"
onto the frame cladding at the jambs and head. Pre-folding
the tape at 1/2" before removing the paper backing will make
it easier to apply the tape correctly. If the siding is less than
1/2" thick, adjust the dimension of the fold so the exterior
sealant line will cover the exterior edge of the tape.
A. Apply side flashing tape. Cut two pieces of flashing tape 5" longer than
the frame height of the window. Apply the tape 1/2" onto the frame
cladding, over the fin and laps onto the water resistive barrier. The tape
should extend 2" above the top of the window and 3" below the bottom
of the window. Press the tape down firmly while folding down the excess
tape at the top and bottom of the window.
B. Apply top flashing tape. Cut two pieces of flashing tape long enough
to go across the top of the window and extend 1" past the flashing
tape on both sides. Apply the tape 1/2" onto the frame cladding,
over the top nailing fin and onto the water resistive barrier.
Press the tape down firmly. Apply the second piece of
ꢄ"
ꢄ#
tape just above and overlapping the first piece of
flashing tape by 1". Press the tape down firmly.
Fold the overlapping tape down, and press all
tape down firmly.
ꢄ#
ꢃꢈ
ꢃꢈ
C. Fold down top flap of water resistive barrier (4C).
ꢄ%
D. Apply flashing tape to diagonal cuts. Cut
pieces of flashing tape at least 1" longer than the
diagonal cuts in the water resistive barrier. Apply
the tape covering the entire diagonal cut in the
water resistive barrier at both upper corners of
the window.
ꢄ$
ꢄ%
Note: Be sure to overlap the top corners (4D).
SECURING THE WINDOW -
FRAME SCREW INSTALLATION
5
Note: If installing the window using installation clips, proceed to Step 6 -
INSTALLATION CLIP METHOD
A. Fixed windows only: On the room
side of fixed windows are a series of
screws which secure the sash into the
frame. ONE AT A TIME, remove each
screw, drill a 1/8" x 1" deep pilot hole
into the rough framing, then insert a
#10 x 3-1/2" corrosion resistant wood
screw. Proceed to Step 6.
Warning: Removing more than one
ꢅ"
ꢁꢃꢎꢀYꢀꢄꢏꢃꢋꢂꢈꢀ
DPSSPTJPOꢀSFTJTUBOU
XPPEꢀTDSFX
screw at a time could allow the sash
to break free from the window frame
which could result in damage to the
sash and/or create the potential for
personal injury.
B. Drill 1/8" x 1" deep pilot holes into the rough framing through the clearance holes in the
unit frame.
C. Fasten the window to the opening by driving #10 x 3-1/2" corrosion resistant wood screws
into each of the pre-drilled clearance holes.
Note: Screws MUST be driven straight or angled slightly toward the exterior to prevent
interference with the lock mechanism. Drive the screws until snug but DO NOT over-
tighten the screws. DO NOT bend or bow the unit frame.
ꢁꢃꢎꢀYꢀꢄꢏꢃꢋꢂꢈꢀDPSSPTJPOꢀ
SFTJTUBOUꢀXPPEꢀTDSFX
ꢁꢃꢎꢀYꢀꢄꢏꢃꢋꢂꢈꢀ
DPSSPTJPOꢀSFTJTUBOU
XPPEꢀTDSFX
ꢅ$
ꢅ$
%SJMMꢀꢃꢋꢇꢈꢀEJBNFUFSꢀQJMPUꢀ
IPMFꢀUISPVHIꢀUIFꢀDMFBSBODF
IPMFꢀJOꢀUIFꢀGSBNF
ꢅ#
ꢅ#
*/5&3*03
SECURING THE WINDOW -
INSTALLATION CLIP METHOD
6
A. Fasten the window to the opening by driving two #8 x 1-1/4"
corrosion resistant screws into the pre-punched holes in the clips.
If clips are bent and fastened to the interior stud/block, install the
screws as close to the bend as possible.
ꢆ"
Note: DO NOT shim above the window. For masonry openings
use two 3/16" x 1-1/2" masonry screws per clip. Pre-drill the
masonry before attempting to drive the screws in.
INTERIOR SEAL
7
Caution: Ensure use of low pressure polyurethane window and door insulating
foams and strictly follow the foam manufacturer’s recommendations for
application. Use of high pressure foams or improper application of the
foam may cause the window frame to bow and hinder operation.
ꢇ"
*OUFSJPS
A. Apply insulating foam sealant. From the interior, insert the nozzle
of the applicator approximately 1" deep into the space between the
window and the rough opening and apply a 1" deep bead of foam.
This will allow room for expansion of the foam and will minimize
squeeze out. If using foam other than Great Stuff ™ Window and
Door Insulating Foam Sealant by the Dow Chemical Company,
allow the foam to cure completely (usually 8 to 24 hours) before
proceeding to the next step.
Note: DO NOT completely fill the space from the back of the fin
to the interior face of the opening.
B. Check window operation (vent units only) by opening and closing the window.
Note: If the window does not operate correctly, check to make sure it is still plumb, level,
square and that the sides are not bowed. If adjustments are required, remove the foam
with a serrated knife. Adjust the shims, and reapply the insulating foam sealant.
SEALING THE WINDOW TO THE
EXTERIOR WALL CLADDING
When applying siding, brick veneer or other exterior finish material, leave adequate space
between the window frame and the material for sealant. Refer to the illustration that
corresponds to your finish material.
8
Note: The sealant details shown are standard recommendations from the sealant industry.
Contact your sealant supplier for recommendations and instructions for these and any
other applications.
4*%*/(
8*5)ꢀ53*.
#3*$,ꢀ7&/&&3
5)*/
4*%*/(
#BDLFSꢀ3PEꢀ
BOE
#BDLFSꢀ3PEꢀBOE
4FBMBOUꢀUZQJDBM
4FBMBOUꢀ
UZQJDBM
4FBMBOUꢀUZQJDBM
ꢃꢋꢅꢈꢀ$MFBSBODF
ꢃꢋꢅꢈꢀ$MFBSBODF
"DDFTTPSZꢀ(SPPWF
ꢃꢋꢇꢈꢀ
$MFBSBODF
*OTVMBUJOH
'PBN
"DDFTTPSZꢀ(SPPWF
*OTVMBUJOH
'PBN
*OTVMBUJOH
'PBN
1FSJNFUFSꢀ4FBMBOUꢀ
NVTUꢀFYUFOEꢀUPꢀ
SPPNꢀTJEFꢀPGꢀ
"DDFTTPSZ
(SPPWF
1FSJNFUFSꢀ4FBMBOUꢀ
NVTUꢀFYUFOEꢀUPꢀ
SPPNꢀTJEFꢀPGꢀ
"DDFTTPSZꢀ(SPPWFꢊ
"DDFTTPSZꢀ(SPPWFꢊ
ꢃꢋꢅꢈ
ꢃꢋꢅꢈ
ꢃꢋꢇꢈ
ꢃꢋꢅꢈ
.JOꢊ
ꢃꢋꢅꢈ
.JOꢊ
7*/:-ꢋ45&&-
4*%*/(
456$$0
#BDLFSꢀ3PEꢀBOE
4FBMBOUꢀUZQJDBM
ꢃꢋꢅꢈꢀ$MFBSBODF
#BDLFSꢀ3PEꢀBOE
4FBMBOUꢀUZQJDBM
ꢃꢋꢅꢈꢀ$MFBSBODF
"DDFTTPSZꢀ(SPPWF
"DDFTTPSZꢀ(SPPWF
*OTVMBUJOH
'PBN
*OTVMBUJOH
'PBN
1FSJNFUFSꢀ4FBMBOUꢀ
NVTUꢀFYUFOEꢀUPꢀ
SPPNꢀTJEFꢀPGꢀ
1FSJNFUFSꢀ4FBMBOUꢀ
NVTUꢀFYUFOEꢀUPꢀ
SPPNꢀTJEFꢀPGꢀ
"DDFTTPSZꢀꢀꢀ(SPPWFꢊ
"DDFTTPSZꢀ(SPPWFꢊ
ꢃꢋꢅꢈ
ꢃꢋꢅꢈ
ꢃꢋꢅꢈ
.JOꢊ
ꢃꢋꢅꢈ
.JOꢊ
A. Insert backer rod into the space around the window to provide approximately 1/4" clearance
between the backer rod and the exterior face of the exterior finish material.
Note: Backer rod adds shape and depth for the sealant line.
B. Apply a bead of high quality exterior grade sealant
to the entire perimeter of the window.
ꢈ"
ꢈ#
C. Shape, tool and clean excess sealant. When finished,
the sealant should be the shape of an hourglass.
Note: This method creates a more flexible sealant line
capable of expanding and contracting.
INTERIOR FINISHING
If products cannot be finished immediately, cover with clear plastic to protect from dirt, damage and
moisture. Remove any construction residue before finishing. Sand all wood surfaces lightly with 180
grit or finer sandpaper. DO NOT use steel wool. BE CAREFUL NOT TO SCRATCH THE GLASS.
Remove sanding dust.
Pella products must be finished per the below instructions; failure to follow these instructions voids the
Limited Warranty.
• On casement and awnings, it is optional to paint, stain or finish the vertical and horizontal sash edges.
• On single-hung and double-hung, do not paint, stain or finish the vertical sash edges, any finish on
the vertical sash edges may cause the sash to stick; it is optional to paint, stain or finish the horizontal
sash edges.
• On patio doors, it is optional to paint, stain or finish the vertical and horizontal panel edges.
Note: To maintain proper product performance do not paint, finish or remove the weather-
stripping, mohair dust pads, gaskets or vinyl parts. Air and water leakage will result if these parts
are removed. After finishing, allow venting windows and doors to dry completely before
closing them.
Pella Corporation is not responsible for interior paint and stain finish imperfections for any product
that is not factory-applied by Pella Corporation. Use of inappropriate finishes, solvents, brickwash, or
cleaning chemicals will cause adverse reactions with window and door materials and voids the
Limited Warranty.
For additional information on finishing see the Pella Owner’s Manual or go to www.pella.com.
EXTERIOR FINISHING
The exterior frame and sash are protected by aluminum cladding with our tough EnduraClad® or
EnduraClad Plus baked-on factory finish that needs no painting. Clean this surface with mild
soap and water. Stubborn stains and deposits may be removed with mineral spirits. DO NOT use
abrasives. DO NOT scrape or use tools that might damage the surface.
Use of inappropriate finishes, solvents, brickwash or cleaning chemicals will cause adverse reactions
with window and door materials and voids the Limited Warranty.
CARE AND MAINTENANCE
Care and maintenance information is available in the Pella Owner’s Manual. You can obtain an owner’s
manual by contacting your local Pella retailer. This information is also available on www.pella.com.
IMPORTANT NOTICE
Because all construction must anticipate some water infiltration, it is important that the wall system be
designed and constructed to properly manage moisture. Pella Corporation is not responsible for claims
or damages caused by anticipated and unanticipated water infiltration; deficiencies in building design,
construction and maintenance; failure to install Pella® products in accordance with Pella installation
instructions; or the use of Pella products in wall systems which do not allow for proper management
of moisture within the wall systems. The determination of the suitability of all building components,
including the use of Pella products, as well as the design and installation of flashing and sealing systems
are the responsibility of the Buyer or User, the architect, contractor, installer, or other construction
professional and are not the responsibility of Pella.
Pella products should not be used in barrier wall systems which do not allow for proper management
of moisture within the wall systems, such as barrier Exterior Insulation and Finish Systems (EIFS) (also
known as synthetic stucco), or other non-water managed systems. Except in the states of
California, New Mexico, Arizona, Nevada, Utah, and Colorado, Pella makes no warranty of any kind
and assumes no responsibility for Pella windows and doors installed in barrier wall systems.
In the states listed above, the installation of Pella products in barrier wall or similar systems must
be in accordance with Pella installation instructions.
Product modifications that are not approved by Pella Corporation will void the Limited Warranty.
INSTALLING ROTO COVER AND CRANK
Note: Finish the interior of the window and allow the window to dry before proceeding with
these instructions. (To open the window for finishing, partially insert the lock handle into the
jamb, unlock the unit, temporarily attach the crank handle and turn to open.)
A. Place the cover over the operator stud and snap into place.
1PDLFUꢀ&OE
#
B. Apply pressure to the pocket end of the cover and snap
into place.
C. Use a medium size flat-blade screwdriver to loosen the set
screw in the crank handle.
"
0QFSBUPSꢀ4UVE
$SBOLꢀ)BOEMF
0QFSBUPSꢀ4UVE
%
D. Slide the crank handle onto the stud. Unlock, open window,
then close and lock window.
E. Fold the crank handle down and check alignment of knob
with the pocket.
4FUꢀ4DSFX $
Note: You may need to adjust the crank position on the
stud until the correct alignment is achieved.
,OPC
&
F. Open the crank and tighten the set screw.
G. After the final installation, fold the crank over and snap the
knob into the pocket.
Note: Even with the window open the crank can be folded
to avoid interfering with the window treatments.
1PDLFU
LOCK LEVER REMOVAL AND INSERTION
Note: You may want to remove the lock lever prior to finishing the window, or if it needs to be
replaced with a lock lever in a different finish.
*OUFSJPS
&YUFSJPS
A. Unlock and open the window.
#
$
B. Place the lock lever in the locked position.
C. From the exterior of the window, insert a small flat
blade screwdriver into the slot behind the lock lever.
D. Pry the cam away from the side of the window by
rotating the screwdriver a quarter turn.
Note: This will release the hook in the lever from
the cam hook.
*OUFSJPS
&YUFSJPS
E. Remove the lock lever by pulling it toward the
interior of the building.
&
F. To install a lock lever, hold it in the lock position
and insert it, from the interior, into the slot until it
snaps into the cam.
%
'
|